Modbus TCP Slave Problem

[savaskorkmaz]

Hi,
I have LM5 with 202112 firmware. I need modbus TCP Slave function and i arranged my residence script like below. I tried with modbus PLC and with some free modbus tool for connection but i received an error like 

"COMMUNICATION ERROR

No connection could be made because the target machine actively refused it 192.168.1.81:502 "

My PC IP 192.1681.70 and LM IP is 192.168.1.81 . Is there a problem with 202112 firmware or there is another problem with script ?

Regards 

if not mb then
  require('genohm-scada.eibdgm')
  require('luamodbus')

  -- list of coil mapping, starting from 0
  coils = { '0/1/112', '0/7/112' }
 
  -- list of register mapping, starting from 0
  registers = { '30/1/1', '30/1/2' }


  -- list of register data types, element count must match registers table
  regdt = { dt.int8, dt.int8 }

  -- knx group write callback
  function knxgroupwrite(event)
    local value

    -- try to find matching coil
    for id, addr in ipairs(coils) do
      if event.dst == addr then
        value = knxdatatype.decode(event.datahex, dt.bool)
        mbetcoils(id - 1, value)
      end
    end

    -- try to find matching register
    for id, addr in ipairs(registers) do
      if event.dst == addr then
        value = knxdatatype.decode(event.datahex, regdt[ id ])
        mbetregisters(id - 1, value)
      end
    end
  end

  -- coil write callback
  function mbwritecoils(coil, value)
    local addr = coils[ coil + 1 ]
    if addr then
      grp.write(addr, value, dt.bool)
    end
  end

  -- register write callback
  function mbwriteregisters(register, value)
    local addr = registers[ register + 1 ]
    if addr then
      grp.write(addr, value, regdt[ register + 1])
    end
  end

  -- knx group monitor, handles group writes
  knxclient = eibdgm:new({ timeout = 0.1 })
  knxclientethandler('groupwrite', knxgroupwrite)

  -- modbus slave, listen on all interfaces and default port 502
  mb = luamodbus.tcp()
  mb:open('192.168.1.70', 502)

  -- setting slave id is optional
  -- mbetslave(1)

  mbetreceivetimeout(0.1)
  mbetmapping(#coils, 0, #registers, 0)

  -- init coils
  for id, addr in ipairs(coils) do
    value = grp.getvalue(addr)
    mbetcoils(id - 1, value)
  end

  -- init registers
  for id, addr in ipairs(registers) do
    value = grp.getvalue(addr)
    mbetregisters(id - 1, value)
  end

  -- set callbacks for coil and register write
  mbetwritecoilcb(mbwritecoils)
  mbetwriteregistercb(mbwriteregisters)
end

-- handle modbus and knx
mb:handleslave()
knxclient:loop(0.1)

[admin]

Replace

Code:

mb:open('192.168.1.70', 502)

With

Code:

mb:open('0.0.0.0', 502)

[savaskorkmaz]

Replace

Code:

mb:open('192.168.1.70', 502)

With

Code:

mb:open('0.0.0.0', 502)

I changed and i received same result. There is no firewall on the system.

[admin]

Do a complete script restart via disable/enable. The same script works fine for me with listen IP changed to 0.0.0.0.