This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.
Logic Machine Forum › LogicMachine eco-system › Hardware v
CanX Equipment

Threaded Mode
CanX Equipment
Evens Offline
Member
Posts: 120
Threads: 24
Joined: Jul 2015
Reputation: 0
#1
13.10.2018, 17:40 (This post was last modified: 13.10.2018, 17:41 by Evens.)
Hi, I have read your articles about CanX and are very interested, I see some benefits and have planned to test it out. 
But I have one concern, when and what type of hardware are you planning to release? And by that, I mean, is it switches? Actuators or sensors?  

I’m trying to make a plan to see where I can use CanX, and where I can use KNX. Because I don’t see by now that I can just use CanX and not KNX. Maby sometime in the future.
 
BR Even Sundgot.
Find
Reply
edgars Offline
Administrator
Posts: 429
Threads: 100
Joined: Jun 2015
Reputation: 45
#2
15.10.2018, 06:15
Hi Evens,
here is the list, but its still fluctuating:
https://forum.logicmachine.net/showthrea...33#pid8133

We will add also LoRa 433 (as a backup channel, canX over LoRa) (free of charge) in some models, so the count of ports might change.
Find
Reply
Evens Offline
Member
Posts: 120
Threads: 24
Joined: Jul 2015
Reputation: 0
#3
15.10.2018, 19:14
Hi Edgars,

Sounds good, but im missing 230V dimmers for LED.

Regarding LoRa 433, what does this mean in practice? RF CanX? or gateway to other systems?

BR Even Sundgot.
Find
Reply
edgars Offline
Administrator
Posts: 429
Threads: 100
Joined: Jun 2015
Reputation: 45
#4
16.10.2018, 06:49
step by step Smile
LoRa 433 will be used as transparent bridge between canX devices. Changable bandwidth and modulation factor. Thus we can define the network range/bandwidth ratio.
Further, we will also have LoRaWAN implementation, but on LM5 Reactor-type device.

We plan to prepare wireless technology comparison table for better understanding of pro & con of each of them.
Find
Reply
Evens Offline
Member
Posts: 120
Threads: 24
Joined: Jul 2015
Reputation: 0
#5
16.10.2018, 20:00
Very interesting, if I understand this correctly. Will the LoRa be a redundancy to wired? So, if the wired bus goes down, the RF takes over? Or have I misunderstood?

BR Even Sundgot.
Find
Reply
Daniel Offline
Administrator
Posts: 4646
Threads: 24
Joined: Aug 2017
Reputation: 207
#6
16.10.2018, 20:03
Correct Smile
------------------------------
Ctrl+F5
Find
Reply
CHOUAIBOU Offline
Member
Posts: 71
Threads: 11
Joined: Jan 2016
Reputation: 1
#7
16.10.2018, 20:10 (This post was last modified: 16.10.2018, 20:13 by CHOUAIBOU.)
(16.10.2018, 06:49)edgars Wrote: step by step Smile
LoRa 433 will be used as transparent bridge between canX devices. Changable bandwidth and modulation factor. Thus we can define the network range/bandwidth ratio.
Further, we will also have LoRaWAN implementation, but on LM5 Reactor-type device.

We plan to prepare wireless technology comparison table for better understanding of pro & con of each of them.

Hi Edgars,
The comparison table you are preparing is very important because there is a lot of stuff (EnOcean, ZigBee, XBee, loRa, Wi-fi, Bluetooth, etc...), and each lobby is fighting to death to promote its wireless technology and for the customer and even an engineer, it is not an easy choice when it comes to design a mix architecture based on wire and wireless technologies.

Thank you for sharing,
B.R,
Chouaibou.
Find
Reply


Forum Jump: