This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.

Figerprint doorlock integration
#1
Could anybody suggest doorlock with open API which I can integrate with smarthome system?
Reply
#2
If you have KNX, I have used eKey in combination with Assa Abloy locks successfully. Works like a dream.


Sent from my iPhone using Tapatalk
Reply
#3
Nuki is a doorlock with open API.
Reply
#4
Abus Wapploxx
Reply
#5
(13.05.2019, 14:40)mjaanes Wrote: If you have KNX, I have used eKey in combination with Assa Abloy locks successfully. Works like a dream.


Sent from my iPhone using Tapatalk

Hello! how do you integrate Assa Abloy locks with Logich Machine? I have to do a similar integration with the "TESA Smartair SOAP API". Can you help me please?

Thanks!
Reply
#6
There is an Logic Machine app for Ekey thsat of course also can be used with the Wiser for KNX or spaceLYnk.
https://forum.logicmachine.net/showthrea...light=ekey
Reply
#7
(16.04.2020, 11:27)pentadom Wrote:
(13.05.2019, 14:40)mjaanes Wrote: If you have KNX, I have used eKey in combination with Assa Abloy locks successfully. Works like a dream.


Sent from my iPhone using Tapatalk

Hello! how do you integrate Assa Abloy locks with Logich Machine? I have to do a similar integration with the "TESA Smartair SOAP API". Can you help me please?

Thanks!


I have the eKey KNX gateway installed. Sends a GA to the KNX bus upon reading a particular fingerprint successfully. I then (via LM or similar) just use a KNX actuator to send Voltage to the lock (same way as eKey).
Hope this is helpful.


Sent from my iPhone using Tapatalk
Reply
#8
(17.04.2020, 08:23)mjaanes Wrote:
(16.04.2020, 11:27)pentadom Wrote:
(13.05.2019, 14:40)mjaanes Wrote: If you have KNX, I have used eKey in combination with Assa Abloy locks successfully. Works like a dream.


Sent from my iPhone using Tapatalk

Hello! how do you integrate Assa Abloy locks with Logich Machine? I have to do a similar integration with the "TESA Smartair SOAP API". Can you help me please?

Thanks!


I have the eKey KNX gateway installed. Sends a GA to the KNX bus upon reading a particular fingerprint successfully. I then (via LM or similar) just use a KNX actuator to send Voltage to the lock (same way as eKey).
Hope this is helpful.


Sent from my iPhone using Tapatalk


And what about Assa Abloy locks? I'm really interested on it
Reply
#9
Many different types of Assa Abloy locks out there. Mine (the EL482) has a built-in solenoid. Sending a 12v pulse to this will open the lock. 12v is provided via a KNX actuator triggered by a GA sent from either the LM or the eKey GW directly.


Sent from my iPhone using Tapatalk
Reply
#10
(27.11.2019, 14:47)Joep Wrote: Nuki is a doorlock with open API.

Hi
do you have a library for communication to Nuki?
The API seems to be complex and having already done and tested library at the begining would be helpful.
LM5Lp, firmware: 2018.08.22 and 2021.12.15, FlashSYS v2, ARMv7 Processor rev 5 (v7l), kernel 4.4.151 and 4.4.259
Reply
#11
(10.05.2021, 14:39)Thomas Wrote:
(27.11.2019, 14:47)Joep Wrote: Nuki is a doorlock with open API.

Hi
do you have a library for communication to Nuki?
The API seems to be complex and having already done and tested library at the begining would be helpful.

I'm at the same boat. I'm trying to integrate my Nuki bridge + Nuki keylock but seems quite difficult with the documentation I have found...
Reply
#12
Is there any progress regarding integration with Nuki? Has anyone succeeded?

https://developer.nuki.io/
https://nuki.io/
Reply
#13
Nuki has a bridge device which can be connected to LM via HTTP requests: https://developer.nuki.io/page/nuki-brid...api-1-12/4
Reply
#14
(05.07.2021, 06:48)admin Wrote: Nuki has a bridge device which can be connected to LM via HTTP requests: https://developer.nuki.io/page/nuki-brid...api-1-12/4

Cool! I'm just going to try it with mine. Thank you!
Reply


Forum Jump: