Problem with remote KNX programming on port 3671

Linear Mode

Problem with remote KNX programming on port 3671

Shimaa Offline

Offline

Junior Member

Posts: 24
Threads: 4
Joined: May 2021
Reputation: 0

#23

02.03.2022, 11:44

(01.03.2022, 15:51)Daniel Wrote: You can use Zerotier, no need for static IP.
https://openrb.com/zerotier-remote-maintenance-of-lm5/

I will try it, Thanks for your time

Find

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Problem with remote KNX programming on port 3671 - by Kilogica - 09.11.2021, 11:18

RE: Problem with remote KNX programming on port 3671 - by Daniel - 09.11.2021, 11:20

RE: Problem with remote KNX programming on port 3671 - by Erwin van der Zwart - 09.11.2021, 13:13

RE: Problem with remote KNX programming on port 3671 - by YOUSSEF - 14.02.2022, 18:26

RE: Problem with remote KNX programming on port 3671 - by Kilogica - 09.11.2021, 13:49

RE: Problem with remote KNX programming on port 3671 - by Daniel - 09.11.2021, 13:50

RE: Problem with remote KNX programming on port 3671 - by Kilogica - 09.11.2021, 14:34

RE: Problem with remote KNX programming on port 3671 - by Daniel - 09.11.2021, 14:35

RE: Problem with remote KNX programming on port 3671 - by Erwin van der Zwart - 10.11.2021, 14:12

RE: Problem with remote KNX programming on port 3671 - by CristianAgata - 10.11.2021, 20:40

RE: Problem with remote KNX programming on port 3671 - by puntukas - 22.11.2021, 10:25

RE: Problem with remote KNX programming on port 3671 - by Erwin van der Zwart - 22.11.2021, 15:21

RE: Problem with remote KNX programming on port 3671 - by Frank68 - 24.11.2021, 11:58

RE: Problem with remote KNX programming on port 3671 - by davidchispas - 11.01.2022, 16:16

RE: Problem with remote KNX programming on port 3671 - by admin - 11.01.2022, 16:18

RE: Problem with remote KNX programming on port 3671 - by Daniel - 11.01.2022, 16:19

RE: Problem with remote KNX programming on port 3671 - by admin - 15.02.2022, 08:11

RE: Problem with remote KNX programming on port 3671 - by Dan22 - 16.02.2022, 16:44

RE: Problem with remote KNX programming on port 3671 - by Daniel - 16.02.2022, 16:50

RE: Problem with remote KNX programming on port 3671 - by Dan22 - 16.02.2022, 17:13

RE: Problem with remote KNX programming on port 3671 - by Shimaa - 01.03.2022, 15:48

RE: Problem with remote KNX programming on port 3671 - by Daniel - 01.03.2022, 15:51

RE: Problem with remote KNX programming on port 3671 - by Shimaa - 02.03.2022, 11:44

RE: Problem with remote KNX programming on port 3671 - by eliasjavierr - 14.07.2023, 01:23

RE: Problem with remote KNX programming on port 3671 - by Daniel - 14.07.2023, 07:56

View a Printable Version