This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.
Logic Machine Forum › LogicMachine eco-system › Gateway v
Z WAVE

Threaded Mode
Z WAVE
hima Offline
Junior Member
Posts: 12
Threads: 4
Joined: Nov 2016
Reputation: 0
#1
09.12.2016, 05:58
Hello,


When the server LM4 was powered OFF and ON ( or else rebooted ), upon z wave configuration page, all the devices are shown as active. But actually none of them works. We need to press the program button of each ( even powered z wave device ) device to wake them up. After this action, it starts working. It is really a pain because some devices are installed at double height locations and every-time waking them is not so reliable. Please give us your suggestion ! 
Regards
Hima
Find
Reply
edgars Offline
Administrator
Posts: 426
Threads: 99
Joined: Jun 2015
Reputation: 44
#2
09.12.2016, 07:17
Hello Hima,

please read this forum thread about wakeup interval:
http://forum.logicmachine.net/showthread...19#pid2719
Find
Reply
hima Offline
Junior Member
Posts: 12
Threads: 4
Joined: Nov 2016
Reputation: 0
#3
12.12.2016, 06:27
We are not able to change this on relay parameter. It goes back to the default value !

Also everytime we need to wake those devices up when there is a power failure. Its tough to open the switch box all the time.
Regards
Hima
Find
Reply
edgars Offline
Administrator
Posts: 426
Threads: 99
Joined: Jun 2015
Reputation: 44
#4
13.12.2016, 10:30
We have tested with Fibaro motion sensor, it is sensor's setting. The controller/LM cannot wake up the device while it doesn't come online itself.

Please let me know what kind of Zwave devices are you using? You are welcome to send me log file to email. You can grab it here: http://IP_LogicMachine/apps/data/zwaveapp/__log.lp
Find
Reply
hima Offline
Junior Member
Posts: 12
Threads: 4
Joined: Nov 2016
Reputation: 0
#5
14.12.2016, 16:09
(13.12.2016, 10:30)edgars Wrote: We have tested with Fibaro motion sensor, it is sensor's setting. The controller/LM cannot wake up the device while it doesn't come online itself.

Please let me know what kind of Zwave devices are you using? You are welcome to send me log file to email. You can grab it here: http://IP_LogicMachine/apps/data/zwaveapp/__log.lp


The issue is with the powered relays and dimmers and not the battery operated devices.

We are using Fibaro relay FGS 211, Fibaro dimmer FGD 211, Fibaro door senor and fibaro universal input interface. We can't setup the polling time on powered devices !
Regards
Hima
Find
Reply
hima Offline
Junior Member
Posts: 12
Threads: 4
Joined: Nov 2016
Reputation: 0
#6
15.12.2016, 07:27
Also one more issue we are facing. The z wave USB is not initializing. Deamon tool is started but no setup for the USB z wave in list of devices. 
Regards
Hima
Find
Reply
gaxy Offline
Junior Member
Posts: 7
Threads: 0
Joined: Aug 2016
Reputation: 0
#7
01.01.2017, 21:31
Hi

I have a PH-PAT02-B.eu Multisensor 2in1, it works more or less ok but i am not able to save the advanced settings, it allway shows me the default settings, i can change them but after the save butten the settings are shown as before.

also i am not able to use the polling checkbox on the basic settings page.

kind regards
Find
Reply
gaxy Offline
Junior Member
Posts: 7
Threads: 0
Joined: Aug 2016
Reputation: 0
#8
05.01.2017, 22:20
any news on that?
Find
Reply


Forum Jump: