CanX and LoRa - Printable Version

CanX and LoRa - Printable Version

+- Logic Machine Forum (https://forum.logicmachine.net)
+-- Forum: LogicMachine eco-system (https://forum.logicmachine.net/forumdisplay.php?fid=1)
+--- Forum: CANx (https://forum.logicmachine.net/forumdisplay.php?fid=23)
+--- Thread: CanX and LoRa (/showthread.php?tid=2031)

CanX and LoRa - Kai-Roger - 15.04.2019

Hi.

I just tested the LoRa communication between two devices. I set up the two devices with same LoRa parameters and the same encrytion key. I then disconnected the CAN connector from one of the devices, and guess what... The two devices continued communication over wireless automatically!! This is fantastic!

BR
Kai-Roger

RE: CanX and LoRa - CHOUAIBOU - 16.04.2019

1 x CAN-UI8-LoRa

(15.04.2019, 21:20)Kai-Roger Wrote: Hi.

I just tested the LoRa communication between two devices. I set up the two devices with same LoRa parameters and the same encrytion key. I then disconnected the CAN connector from one of the devices, and guess what... The two devices continued communication over wireless automatically!! This is fantastic!

BR
Kai-Roger

Hello Kai,
Great ! Good news !

B.R,
Chouaibou.

RE: CanX and LoRa - HannPark - 15.08.2019

I have the UIO8(8 universal IO ports +loRa) and R4 (4 Relay outputs + LoRa), I did the same but when i disconnected the CAN connector in the R4 the trasmit light in UIO8 lights up and the receive Light in the R4 lights up at the same time but nothing happends, the relay isn´t activating :/

RE: CanX and LoRa - edgars - 16.08.2019

Hi there,
please make sure to upgrade the CANx devices to the latest firmware:
https://dl.openrb.com/canx/

Follow this guide and install the software from here (at the bottom of the page):
https://openrb.com/canx-technology/

Then upgrade CANx app on LogicMachine.

Then try reconfigure following this guide:

RE: CanX and LoRa - HannPark - 16.08.2019

Hi,
I just uploaded the last firmware to my devices,

r4-lora_20190701.dfu
uio8-lora_20190701.dfu

And update my CANx App on LM, and I used the same loRa config from the video guide, using as a gateway the UIO8 and the R4 in Device Mode, but the problem persist... It work over CAN but when I disconnect the CAN wire on the R4, it stop working, but the orange light labeled as "T" in UIO8 lights up... and in the R4 a blue one turns on at the same time...

Thanks for ur support...

RE: CanX and LoRa - balatis - 02.04.2020

Hello
I have same problem , i did update last firmwear on canx devices and canx apk. I have comunication with cable but when remove one device from network does not work with lora
Thanks in advance.

RE: CanX and LoRa - admin - 03.04.2020

Try using these firmwares: https://dl.openrb.com/canx-new/
Make sure that all LoRa devices are using updated fws. And perform reset on all devices by holding programming button for 5 seconds. Release the button once red LED starts flashing.

RE: CanX and LoRa - balatis - 03.04.2020

(16.08.2019, 15:32)HannPark Wrote: Γεια σας,
θα ήθελα απλώς ανεβάσει το τελευταίο firmware για τις συσκευές μου,

R4-lora_20190701.dfu
uio8-lora_20190701.dfu

Και ενημερώσετε canx App μου για LM, και χρησιμοποίησα το ίδιο Lora ρυθμίσεων από τον οδηγό βίντεο, χρησιμοποιώντας ως πύλη η UIO8 και το R4 στο Device Mode, αλλά το πρόβλημα παραμένει ... Δουλεύει πάνω από CAN αλλά όταν αποσυνδέω το καλώδιο CAN στο R4, σταματά να λειτουργεί, αλλά το πορτοκαλί φως που φέρει την ένδειξη "T" στο UIO8 ανάβει ... και σε το R4 ένα μπλε ενεργοποιεί την ίδια στιγμή ...

Ευχαριστώ για την υποστήριξη ur ...

(03.04.2020, 06:33)admin Wrote: Δοκιμάστε να χρησιμοποιήσετε αυτά τα firmware: https://dl.openrb.com/canx-new/
Βεβαιωθείτε ότι όλες οι συσκευές LoRa χρησιμοποιούν ενημέρωση fws. Και πραγματοποιήστε επαναφορά σε όλες τις συσκευές κρατώντας το πλήκτρο προγραμματισμού για 5 δευτερόλεπτα. Αφήστε το κουμπί μόλις αρχίσει να αναβοσβήνει το κόκκινο LED.

Hi admin
i did update and work the lora , but the uio8 does not work inputs and outputs i loaded this firmwear (uio8-lora_20200319)
Thanks in advance

RE: CanX and LoRa - Daniel - 06.04.2020

Hi
Try this firmware
https://dl.openrb.com/canx-new/uio8-lora_20200406-2.dfu
Works well for me.

RE: CanX and LoRa - balatis - 06.04.2020

(06.04.2020, 12:26)Daniel. Wrote: Hi
Try this firmware
https://dl.openrb.com/canx-new/uio8-lora_20200406-2.dfu
Works well for me.

Hi
Yes it work!!!

RE: CanX and LoRa - rw_echo - 15.09.2023

In the can lora system,How can I program or change programs for can-lora devices that are not connected to the can bus through LM (can)?Can anyone help me?

Thanks in advance.

RE: CanX and LoRa - admin - 15.09.2023

For security reasons parameters can only be changed via wired CAN connection but not over radio.

RE: CanX and LoRa - rw_echo - 18.09.2023

In practical use, devices controlled solely through LORA communication must be connected to the can bus to complete program configuration before installation,right?

RE: CanX and LoRa - admin - 18.09.2023

Yes, all configuration is done via wired CANx bus connection.