This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.
Logic Machine Forum › LogicMachine eco-system › Hardware v
Connection from different NET

Threaded Mode
Connection from different NET
Frank68 Offline
Senior Member
Posts: 342
Threads: 130
Joined: May 2020
Reputation: 0
#1
21.11.2023, 08:06
Greetings
I would need to be able to access the LM from different subnets:
192.168.1.n
192.168.2.n
I tried to change the subnet to 255.255.252.0 but to no avail, is there something in the LM that blocks access from different networks?
Find
Reply
forsterm Offline
Junior Member
Posts: 40
Threads: 2
Joined: Mar 2017
Reputation: 3
#2
21.11.2023, 08:11
See this: https://forum.logicmachine.net/showthrea...2#pid16682

(21.11.2023, 08:06)Frank68 Wrote: Greetings
I would need to be able to access the LM from different subnets:
192.168.1.n
192.168.2.n
I tried to change the subnet to 255.255.252.0 but to no avail, is there something in the LM that blocks access from different networks?
Best regards

forsterm
Find
Reply
Frank68 Offline
Senior Member
Posts: 342
Threads: 130
Joined: May 2020
Reputation: 0
#3
21.11.2023, 13:38
(21.11.2023, 08:11)forsterm Wrote: See this: https://forum.logicmachine.net/showthrea...2#pid16682

(21.11.2023, 08:06)Frank68 Wrote: Greetings
I would need to be able to access the LM from different subnets:
192.168.1.n
192.168.2.n
I tried to change the subnet to 255.255.252.0 but to no avail, is there something in the LM that blocks access from different networks?

I not ned more LM on the net i need more computer from different net able to connect to the same LM, i have the vlan but is all open.
Find
Reply
admin Offline
Administrator
Posts: 8125
Threads: 43
Joined: Jun 2015
Reputation: 471
#4
21.11.2023, 13:39
This has to be configured on your router. Make sure that LM has a correct gateway set. Keep netmask as 255.255.255.0.
Find
Reply
Frank68 Offline
Senior Member
Posts: 342
Threads: 130
Joined: May 2020
Reputation: 0
#5
22.11.2023, 07:34
(21.11.2023, 13:39)admin Wrote: This has to be configured on your router. Make sure that LM has a correct gateway set. Keep netmask as 255.255.255.0.

Hi, I have the corret SN and GW , but nothing, is not possible to reach the LM from different network, if I set more I,
IN the LM I use Zerotier for remote connection and if i set more IP ZeroTier not work.
how can I solve it ?

Thank's
Find
Reply
admin Offline
Administrator
Posts: 8125
Threads: 43
Joined: Jun 2015
Reputation: 471
#6
22.11.2023, 10:07
Having an extra IP address should not affect ZeroTier unless you have the same network on both eth0 and virtual ZeroTier interface.

If you have several subnets on the same LAN then you should be able to connect to LM using both IP addresses. Of course, the connecting device should also belong to the same subnet.

If subnets are not different LANs then your router must be configured to accept and route traffic between these subnets. In this case LM does not need an extra IP address.
Find
Reply


Forum Jump: