This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.

KnxNet/IP - bug ?
#1
Exclamation 
Hi,

this is a few (low-level) questions about the KnxNet/IP implementation on Logic Machine 5.

I too a look at UDP-packages in Wireshark while connecting to LM5 with ETS5, and found some anomalies.

1) In system settings -> KNX Settings, I specified that I want EIBNet/IP Tunnelling. However, LM5 keeps sending ROUTING_INDICATION packages ?


2) When doing a CONNECTIONSTATE_REQUEST, the CONNECTIONSTATE_RESPONSE  should contain one of the status codes:

E_NO_ERROR = 0x00,
E_CONNECTION_ID = 0x21,
E_DATA_CONNECTION = 0x26,
E_KNX_CONNECTION = 0x27

However, LogicMachine replies with code 0x15, which is an unknown status. Output from WireShark:

Request:
Code:
Frame 729: 58 bytes on wire (464 bits), 58 bytes captured (464 bits) on interface 0
Ethernet II, Src: Giga-Byt_28:b3:64 (fc:aa:14:28:b3:64), Dst: OpenrbCo_26 (00:1b:c5:00:10:26)
Internet Protocol Version 4, Src: 10.20.25.30, Dst: 10.20.25.123
User Datagram Protocol, Src Port: 52989, Dst Port: 3671
KNXnet/IP
    Header
        Header Length: 0x06
        Protocol Version: 0x10
        Service Type Identifier: CONNECTIONSTATE_REQUEST (0x0207)
        Total Length: 16 octets
    Body
        Communication Channel ID: 1
        reserved: 00
        HPAI: Control endpoint
            Structure Length: 8 octets
            Host Protocol Code: IPV4_UDP (0x01)
            IP Address: 10.20.25.30
            IP Port: 52988

HEX:
0000   06 10 02 07 00 10 01 00 08 01 0a 14 19 1e ce fc

Response:


Code:
Frame 730: 60 bytes on wire (480 bits), 60 bytes captured (480 bits) on interface 0
Ethernet II, Src: OpenrbCo_26 (00:1b:c5:00:10:26), Dst: Giga-Byt_28:b3:64 (fc:aa:14:28:b3:64)
Internet Protocol Version 4, Src: 10.20.25.123, Dst: 10.20.25.30
User Datagram Protocol, Src Port: 3671, Dst Port: 52988
KNXnet/IP
    Header
        Header Length: 0x06
        Protocol Version: 0x10
        Service Type Identifier: CONNECTIONSTATE_RESPONSE (0x0208)
        Total Length: 8 octets
    Body
        Communication Channel ID: 1
        Status: Unknown (0x15)

HEX:
0000   06 10 02 08 00 08 01 15
3) I tried to perform a line scan in ETS5, but no devices show up. I haven't analyzed the traffic (yet) for this issue.
I am currently implementing a KnxNet/IP client, which is why I stumbled across these issues.
Reply


Messages In This Thread
KnxNet/IP - bug ? - by oyvindi - 29.03.2017, 12:41
RE: KnxNet/IP - bug ? - by admin - 29.03.2017, 13:20
RE: KnxNet/IP - bug ? - by oyvindi - 29.03.2017, 13:37

Forum Jump: