Display time of object

[Nir70]

Hello

Is it possible to display the operation time of an object (lamp, air conditioner) in minutes on screen  . Thanks

[admin]

Do you mean the time since the last ON command or the overall running time?

[Nir70]

Do you mean the time since the last ON command or the overall running time?

Hello

yes, the time since the last ON command . Thanks

[admin]

You will need two scripts for this.
1. Event script mapped to control or status object if the load:

Code:

value = event.getvalue()
key = 'ontime'
out = '32/1/5'

if value then
  if not storage.get(key) then
    storage.set(key, os.time())
    grp.update(out, '0m')
  end
else
  storage.delete(key)
  grp.update(out, '')
end

2. Scheduled script that runs every minute:

Code:

key = 'ontime'
out = '32/1/5'

time = storage.get(key)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
  
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
  
  res = res .. minutes .. 'm'
  grp.update(out, res)
end

32/1/5 is the object that shows the load ON time, set data type to 250 byte string. If you need multiple status outputs then use a unique storage key for each load (ontime in this example).

[Nir70]

You will need two scripts for this.
1. Event script mapped to control or status object if the load:

Code:

value = event.getvalue()
key = 'ontime'
out = '32/1/5'

if value then
  if not storage.get(key) then
    storage.set(key, os.time())
    grp.update(out, '0m')
  end
else
  storage.delete(key)
  grp.update(out, '')
end

2. Scheduled script that runs every minute:

Code:

key = 'ontime'
out = '32/1/5'

time = storage.get(key)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
 
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
 
  res = res .. minutes .. 'm'
  grp.update(out, res)
end

32/1/5 is the object that shows the load ON time, set data type to 250 byte string. If you need multiple status outputs then use a unique storage key for each load (ontime in this example).

Small request Can I display seconds? Thanks

[admin]

Yes, set display mode to value or icon/value.

[Nir70]

Yes, set display mode to value or icon/value.

Hello

It works, but it shows me the time only after shutdown ( send 0) , is it possible to view the time in real time?

[admin]

The scheduled script should update the value each minute, check that it is set up correctly

[Nir70]

I checked does not update in real time, only I send a shutdown (0) it displays.

[admin]

What is the data type of control object that is mapped to an event script?

[Nir70]

1 bit lamp, what do you mean?

[admin]

1 bit is ok because it won't work correctly for non-Boolean values. Are you sure the value is not inverted because sending Off should put an empty string as the run-time value. Check if you have modified the scripts in any way.

[Dré]

The scheduled script should update the value each minute, check that it is set up correctly

I tried this scipt too and use it now for 28 minutes and it is counting.

did you post the seconds script in a 'scheduled script' ?

[khalil]

Thanks admin
The Script work fine for me and I add last run interval when value become false instead of nothing 

Code:

value = event.getvalue()
key = 'ontime'
out = '40/1/7'

if value then
  if not storage.get(key) then
    storage.set(key, os.time())
    grp.update(out, '0m')
  end
else
  Last_Run = grp.getvalue(out)
  time = os.date(' %a, %d/%m',time)
  grp.update(out, 'Last Run: '..Last_Run..' In'..time)
  storage.delete(key)
end

[Dré]

You will need two scripts for this.
1. Event script mapped to control or status object if the load:

Code:

value = event.getvalue()
key = 'ontime'
out = '32/1/5'

if value then
  if not storage.get(key) then
    storage.set(key, os.time())
    grp.update(out, '0m')
  end
else
  storage.delete(key)
  grp.update(out, '')
end

2. Scheduled script that runs every minute:

Code:

key = 'ontime'
out = '32/1/5'

time = storage.get(key)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
 
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
 
  res = res .. minutes .. 'm'
  grp.update(out, res)
end

32/1/5 is the object that shows the load ON time, set data type to 250 byte string. If you need multiple status outputs then use a unique storage key for each load (ontime in this example).

I have a question, i try to use this script more times
i change the names value, key and out on both of the script on all places.
so both scripts use different names.

but if i trigger the seconds action, the first timer start for 0 again, some know what i do wrong?

my first event script for Laptop Table

Code:

Laptop_Table = event.getvalue()        --'0 WCD Woonkamer - laptoplader eettafel (tm)'
ontime_Laptop_Table = 'ontime'
output_Laptop_Table = '32/1/201'    --'Laptop eettafel [timer on]'        

if Laptop_Table then
  if not storage.get(ontime_Laptop_Table) then
    storage.set(ontime_Laptop_Table, os.time())
    grp.update(output_Laptop_Table, '0 m')
  end
else
  storage.delete(ontime_Laptop_Table)
  grp.update(output_Laptop_Table, '')
end

my first Resident script for Laptop Table

Code:

ontime_Laptop_Table = 'ontime'
output_Laptop_Table = '32/1/201'            --'Laptop eettafel [timer on]'    

time = storage.get(ontime_Laptop_Table)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
  
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
  
  res = res .. minutes .. ' minuten'
  grp.update(output_Laptop_Table, res)
end

my second event script for Kitchen

Code:

Kitchen = grp.getvalue('1/4/4')            --'0 Verl. Kitchen (tm)'
ontime_Kitchen = 'ontime'
output_Kitchen = '32/1/202'            --'Kitchen [timer on]'    

if Kitchen then
  if not storage.get(ontime_Kitchen) then
    storage.set(ontime_Kitchen, os.time())
    grp.update(output_Kitchen, '0 m')
  end
else
  storage.delete(ontime_Kitchen)
  grp.update(output_Kitchen, '')
end

my first Resident script for Kitchen

Code:

ontime_Kitchen = 'ontime'
output_Kitchen = '32/1/202'            --'Kitchen [timer on]'

time = storage.get(ontime_Kitchen)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
  
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
  
  res = res .. minutes2 .. ' minuten'
  grp.update(output_Kitchen, res)
end

another thing,
for me it looks like line 1 and line 4 of the Resident script look like do the same thing, or m i wrong?

[Nir70]

Hello Thank you for the help It also works with the last time it was activated.

[admin]

@Dré, you need to change the storage key ('ontime'), not the variable name:

Code:

Kitchen = grp.getvalue('1/4/4')            --'0 Verl. Kitchen (tm)'
ontime_Kitchen = 'ontime_kitchen'
output_Kitchen = '32/1/202'            --'Kitchen [timer on]'    

if Kitchen then
  if not storage.get(ontime_Kitchen) then
    storage.set(ontime_Kitchen, os.time())
    grp.update(output_Kitchen, '0 m')
  end
else
  storage.delete(ontime_Kitchen)
  grp.update(output_Kitchen, '')
end

Code:

ontime_Kitchen = 'ontime_kitchen'
output_Kitchen = '32/1/202'            --'Kitchen [timer on]'

time = storage.get(ontime_Kitchen)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
  
  hours = math.floor(minutes / 60)
  minutes = minutes % 60

  if hours > 0 then
    res = hours .. 'h '
  else
    res = ''
  end
  
  res = res .. minutes2 .. ' minuten'
  grp.update(output_Kitchen, res)
end

If using multiple timers you can combine the scheduled/resident scripts into one.

[Dré]

Thanks Admin & khalil.

i update the script so i have now a time like '00:05' and i also use the last time actived, what Khalil added.


My updated Resident script, thanks for both of you, without i could't make it.

Code:

ontime_Laptop_Table = 'ontime_Laptop_Table'
output_Laptop_Table = '32/1/201'            --'Laptop tafel [timer on]'    

time = storage.get(ontime_Laptop_Table)
if time then
  delta = os.time() - time
  minutes = math.floor(delta / 60)
 
  hours = math.floor(minutes / 60)
  minutes = minutes % 60
  minutes = string.format("%02d", minutes)
       
  if hours > 0 then
    res = hours -- .. ': '
  else
    res = '00:'
  end
  hours = string.format("%02d", hours)
  time_online = hours ..':'..minutes
      
  grp.update(output_Laptop_Table, time_online)
end

Yes and i also can use now more timers of this.

[Nir70]

Hello

I noticed whan  scrap is working. The processor is working hard, and the heat in the processor is rising a lot, is this a normal condition? Why is this happening? Best regards

[admin]

Make sure you use a scheduled script that runs every minute not a resident script with low or 0 sleep time.