Button dimming (8-bit value)

[Jayce]

Hey,

I'm trying to dim a RGB led strip using nothing but a button and logic machine. Basically what I need is to get 8-bit value from a button so that when I hold the button, value toggles between going up and down. Is this possible? If not, what is the best way to control dimming dali lights using a simple button (or two, one up one down), preferably without using any scripts.

[Erwin van der Zwart]

Hi,

Check this article: https://forum.logicmachine.net/showthrea...38#pid1238

BR,

Erwin

[Jayce]

Hi,

Check this article: https://forum.logicmachine.net/showthrea...38#pid1238

BR,

Erwin

Thank you very much for help, bear in mind I'm a beginner though. I tried what you posted about 3bit dimming object, got to a point where i'm supposed to set value after _ in longpresstime_xx. I can't seem to find longpresstime_xx anywhere in the javascript that I pasted in custom javascript. Could you help me please?

EDIT: Nevermind, I figured it out but now I'm having problems with linking the dim UP and DOWN buttons to a real physical buttons I have set up and to the RGB led strip.

[Erwin van der Zwart]

Hi,

You could try something like this:

Code:

1234567891011121314151617181920212223242526272829

addressbyteoutput = '32/1/1' stepsize = 10 value = event.getvalue() current = grp.getvalue(addressbyteoutput) if value < 8 then  if current <= stepsize then    output = 0    if current ~= output then      grp.write(addressbyteoutput, output)    end  else    output = current - stepsize    if current ~= output then      grp.write(addressbyteoutput, output)    end  end elseif value > 8 then  if current >= (100 - stepsize) then    output = 100    if current ~= output then      grp.write(addressbyteoutput, output)    end  else    output = current + stepsize    if current ~= output then      grp.write(addressbyteoutput, output)    end  end end

BR,

Erwin

[Jayce]

Hello,

Excuse me again, how do I try that? Where should I put the script and what should the addressbyteoutput address be? As I said I'm a beginner, if you have time, could you please walk me through this?

Right now I'm in a state where I have done all from the link you sent me, I have two buttons in my visualization, one UP and one DOWN, both have longpresstime set to 10 (1 second). Also, I have 1/1/199, which is my LED strip that I scanned from dali section in LM, I can control the strip with 1 byte unsigned integer.

[Erwin van der Zwart]

Hi,

Just create a 4 bit object that is connected to your physical KNX pushbutton (dimming object), add the script as event based to this object, create a byte SCALE object for your RGB DALI unit and set this object (1/1/199) as addressbyteoutput.

Then it should work..

But do i understand it correct from your last post that you use LM dali interface? If that is the case you should be able to use the commands from http://openrb.com/docs/dali.htm and then you should not be needing this script..

BR,

Erwin

[Jayce]

Yes, I'm using Logic Machines DALI Gateway, sorry for not mentioning earlier.

[Jayce]

Sorry to bother again but would you mind walking me through the method with dali commands you said? Also, what I mean by dimming the RGB strip with pushbutton is that when I hold the button the value goes gradually up. Not sure if I mention this either.

[Erwin van der Zwart]

Hi,

How are you going to config the pushbutton? 
As 4 bit dimming?

BR,

Erwin

[Jayce]

Hello,

Yes, I have set the pushbutton so it is 1bit switching and 3bit dimming. That makes 4bit.

[admin]

We plan to implement 4-bit dimming in DALI gateway plugin soon.

[Bobby]

Is it possible to make a single switch:
1 short push , toggle on / off (remember last state if dimmed)
1 long push, dim up and for next long push, dim down and so on?

[Jayce]

It doesn't have to be 4bit for me, is there any way to make it work so a pushbutton controls dimming of a dali light when using LMs dali gateway? All I'd like it to do is to dim up/down while I hold the button.

Thank you.

[Daniel]

Hi
You can do it as fallow.
Create 4 bit dim object 3.007 and let all parameters as default.
Create event based script on this object and use this script.

Code:

123456789101112131415161718192021222324252627282930313233343536373839

step = 10    --dimming step stepTime = 0.5  --- dimming interval ballastAddress = 1   gatewayID='internal' ----------------------------------------------------------------------------------------------------- valuein = event.getvalue() require('user.dali')    res, err = dalicmd(gatewayID, 'queryactual', { addrtype = 'short', address = ballastAddress })  -- read ok         if res then      status = res:byte()         end while( valuein==11 ) do  status = status + step     if (status >254) then              dalicmd(gatewayID, 'arc', { addrtype = 'short', address = ballastAddress, value = 254})          else      dalicmd(gatewayID, 'arc', { addrtype = 'short', address = ballastAddress, value = status})     end  valuein = grp.getvalue(event.dst)  os.sleep(stepTime) end     while( valuein==3 ) do  status = status - step      if (status <0) then          dalicmd(gatewayID, 'arc', { addrtype = 'short', address = ballastAddress, value = 0})          else        dalicmd(gatewayID, 'arc', { addrtype = 'short', address = ballastAddress, value = status})      end    valuein = grp.getvalue(event.dst)  os.sleep(stepTime) end

Modify parameters
Add this object on to visu and test.
Should work :
Dalli arc is logarithmic curve so you will have slower dim on low values and fast on bigger.

BR

[Jayce]

Works very well, thank you very much.

[alexll]

Hi,

You could try something like this:

Code:

1234567891011121314151617181920212223242526272829

addressbyteoutput = '32/1/1' stepsize = 10 value = event.getvalue() current = grp.getvalue(addressbyteoutput) if value < 8 then  if current <= stepsize then    output = 0    if current ~= output then      grp.write(addressbyteoutput, output)    end  else    output = current - stepsize    if current ~= output then      grp.write(addressbyteoutput, output)    end  end elseif value > 8 then  if current >= (100 - stepsize) then    output = 100    if current ~= output then      grp.write(addressbyteoutput, output)    end  else    output = current + stepsize    if current ~= output then      grp.write(addressbyteoutput, output)    end  end end

BR,

Erwin

Hello. I'm trying this event script with a 4 bit object from KNX, but it only dimms with many "long-pressed" actions, and not mantaining the KNX button switch. Is it the problem on the KNX side or script's?

[admin]

Why do you need a script if this switch supports "dimming steps" mode?

[alexll]

Why do you need a script if this switch supports "dimming steps" mode?

Is that the solution? I've never used that option. I'm going to try that. Thank you!

Edit: Confirmed. It works using "dimming steps" option + your 4 bit object dimming script. It has to be done like that because I needed to dim some Philips Hue LED strips from a KNX single button.