This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm that you accept these cookies being set.

FBEditor log write
#1
Hi
There's a log write in fbe_hysteresis_3_limits function. Can I disable this log write? I use this function for brightness evaluation and it can write 70 pages of log every day.

Code:
require('custom.fbeditor20.Control')

Input = 555
Limit_1_ON = 400
Limit_1_OFF = 300
Limit_2_ON = nil
Limit_2_OFF = nil
Limit_3_ON = nil
Limit_3_OFF = nil
threshold1, threshold2, threshold3 = fbe_hysteresis_3_limits(Input, Limit_1_ON, Limit_1_OFF, Limit_2_ON, Limit_2_OFF, Limit_3_ON, Limit_3_OFF, 'fb__New_diagram__fbe_hysteresis_3_limits__id')


In log I see:

Code:
* table:
[1]
 * number: 1
[2]
 * number: 0
[3]
 * number: 0
LM5Lp, firmware: 2018.08.22 and 2021.12.15, FlashSYS v2, ARMv7 Processor rev 5 (v7l), kernel 4.4.151 and 4.4.259
Reply
#2
Hi
Here are all the functions used in FB Editor
https://forum.logicmachine.net/showthrea...=fb+editor
Find yours, import to user libraries, correct what you need and you can use it in FB under user blocks.

BR
------------------------------
Ctrl+F5
Reply
#3
Thank you
FYI FBE_Blocks_Control.luas
is the issue

Code:
--- [Function] fbe_hysteresis_3_limits
--- Hysteresis with 3 limits
--- [Comment]
--- The module evaluates an input value in dependence on 3 freely definable limits (3 switch-on and 3 switch-off values).
--- When the limits are exceeded or dropped below, the outputs 1-3 are controlled operated.
--- If a limit has been exceeded (dropped below), first the limit must be dropped below (exceeded) again, before the output can be sent again if the limit is exceeded (dropped below) again.
--- [Input]
--- Input [object]
--- Limit 1 ON [value]
--- Limit 1 OFF [value]
--- Limit 2 ON [value]
--- Limit 2 OFF [value]
--- Limit 3 ON [value]
--- Limit 3 OFF [value]
--- [Output]
--- threshold1 - Threshold 1 [object, storage]
--- threshold2 - Threshold 2 [object, storage]
--- threshold3 - Threshold 3 [object, storage]
function fbe_hysteresis_3_limits(input, on1, off1, on2, off2, on3, off3, blockID)
 local on = { on1, on2, on3 }
 local off = { off1, off2, off3 }
 local prevState = storage.get(blockID .. "_prevState") or {}
 local out = {}
 log(on)
 log(off)
 log(prevState)
 for i=1,3 do
   local state = 0
   if on[i] ~= nil and input > on[i] then
       state = 1
     elseif off[i] ~= nil and input < off[i] then
       state = -1
     end
   if state == 0 or prevState[i] == nil or prevState[i] == state then
     out[i] = nil
   else
     out[i] = state > 0
   end
   prevState[i] = state
 end
 storage.set(blockID .. "_prevState", prevState)
 return out[1], out[2], out[3]
end
LM5Lp, firmware: 2018.08.22 and 2021.12.15, FlashSYS v2, ARMv7 Processor rev 5 (v7l), kernel 4.4.151 and 4.4.259
Reply


Forum Jump: